AMS50
ANTONY MICHAELSON SIGNATURE
50W Pure Class A Dual Mono Power Amplifier
Thank you for purchasing the Musical Fidelity AMS50.
The AMS50 uses the latest in low distortion circuitry in a bridged configuration which delivers 50 watts of pure class A power.
The AMS50 is designed with pure undistorted experience in mind. Overall the listening experience is greatly improved because of
dramatically lower distortion and increased dynamic range.
The AMS50 accepts both XLR balanced and RCA line level inputs. When driven from a balanced pre-amplifier the sound
quality is greatly improved because the balanced cable cancels out noise and interference artefacts, giving up to 12dB increase in
dynamic range.
The Primo Pre-amplifier is an ideal partner as it features a fully valve signal path and true balanced operation throughout
Alternatively, the AMS50 can be used as a conventional power amplifier driven by a high quality preamp.
The AMS50 is a perfect answer to pure musicality in a single beautifully engineered package. Used properly and carefully, it
should give many years of outstanding musical reproduction.
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing agents - they may harm the surface
finish.
If there are further questions about any Musical Fidelity component, please consult the dealer from whom it was purchased, who is
there to help and give advice.
SAFETY INFORMATION
AMS50
IMPORTANT! (U.K. only)
This unit is supplied in the U.K. with mains lead fitted with a moulded 13 amp plug. If, for any reason, you need to cut off the
plug, please remove the fuse holder and dispose of the plug safely, out of reach of children. It must not be plugged into a mains
outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance with the following code:
Green and yellow..............Earth
Blue................................Neutral
Brown.................................Live
WARNING - This appliance MUST be earthed
As the colours of the wires of the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or
coloured green or green-and-yellow, or by the earth symbol :
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
If connecting to a BS1363 plug, a 13 amp fuse must be used.
WARNING:
ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY APPROVED
BY MUSICAL FIDELITY WHO IS THE PARTY RESPONSIBLE FOR
STANDARDS COMPLIANCE COULD VOID THE USER'S AUTHORITY TO
OPERATE THIS EQUIPMENT.
Issue 1
Page 3 of 12
GENERAL ADVICE
AMS50
INSTALLATION PRECAUTIONS and USER INFORMATION
Your new AMS50 is designed and built to provide trouble-free performance, but as with all electronic devices it is necessary to
observe a few precautions:
This unit features a BRIDGED speaker output and should NOT be grounded on either speaker output terminal as both
terminals are effectively “hot”, i.e. carry signal. Please check if using any active “sub”, electrostatic, or other non standard
potentially grounded speaker types directly connected to the outputs of the AMS50. Consult speaker manual or supplier if
in doubt.
Heed all warnings shown on the back of the product.
Only connect the AMS50 to a mains outlet having the same voltage as marked at the back of the unit.
Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is switched off.
Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by items placed on
them.
Do not use near water, or place water-filled containers on the AMS50, for example, a flower vase or potted plants. If
water does spill inside, immediately pull out the mains plug from the wall socket and inform your dealer, who
should then check the unit before further use. Entry of liquid into the AMS50 is dangerous, and may cause electric
shock or fire hazard.
Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.
Do not remove any covers or try to gain access to the inside. There are no internal adjustments or fuses you can replace
yourself. Refer all service work to an authorised Musical Fidelity agent.
Note: Unauthorised opening of the equipment will invalidate any warranty claim.
Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they may harm the surface
finish.
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by lightning. For
protection of your audio system during electrical storms, remove the mains plugs and disconnect any aerial lead.
If after-sales service is required, to help your dealer identify the AMS50 please quote the serial number located on the rear panel of
the unit.
Issue 1
Page 4 of 12
ITEM DISPOSAL INFORMATION
AMS50
DISPOSAL
AFVAL
The crossed out wheeled bin label that appears on the
back panel of the product indicates that the product must not be
disposed of as normal household waste. To prevent possible harm
to the environment please separate the product from other waste to
ensure that it can be recycled in an environmentally safe manner.
Please contact local government office or retailer for available
collection facilities.
Het label op de achterzijde van dit apparaat, een
afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit
apparaat niet samen met gewoon huishoudafval mag worden
weggegooid. Om mogelijke schade aan onze leefomgeving te
voorkomen dient dit apparaat, gescheiden van gewoon
huishoudelijk afval, te worden afgevoerd zodat het op een
milieuvriendelijke manier kan worden gerecycled. Neem voor
beschikbare inzamelplaatsen contact op met uw gemeentelijke
reinigingsdienst of met uw elektronica leverancier.
DISPOSITION
La poubelle sur roulettes barrées X, qui apparaît en logo
sur le panneau arrière du produit, indique que celui-ci ne doit pas
être traité comme un déchet domestique commun. Afin de protéger
l'environnement, ce produit électronique devra être géré
séparément et donc recyclé selon les nouvelles normes
Européennes Rohs concernant les déchets d'appareils électroniques.
Prière de contacter les services concernés gouvernementaux ou
votre point de vente pour l'élimination et l'enlèvement de déchets
électroniques équipés de composants électroniques.
HÄVITTÄMINEN
Yliruksattua jäteastiaa kuvaava tarra tuotteen
takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina
talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä
erillään muusta jätteestä ja se on kierrätettävä ekologisesti
kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan
Ympäristökeskukseen lähimmän kierrätyskeskuksen löytämiseksi.
AFSKAFNING
DISPOSAL
Logoet med en skraldespand med kryds over på bagsiden
af apparatet indikerer at dette produkt ikke må kasseres som normal
husholdningsaffald. For at forebygge mulig skade på miljøet, bedes
De separere dette produkt fra andet affald, og sikre at det bliver
genbrugt på en miljørigtig måde. Kontakt venligst de lokale
myndigheder eller din forhandler for oplysning om nærmeste
tilgængelige opsamlingssted for elektronikaffald.
La etiqueta cruzada hacia fuera del compartimiento que
aparece en el panel trasero del producto indica que el producto no
se debe reciclarse como basura normal de la casa. Para prevenir
daños posible al ambiente separe por favor el producto de otras
basura para asegurarse de que puede ser reciclada de una manera
ambientalmente segura. Entre en contacto por favor a su oficina
gubernamental local o a su minorista para las instalaciones
disponibles de la colección.
∆ΙΑ∆ΙΚΑΣΙΑ ΑΠΟΡΡΙΨΗΣ
ΤΟ
ΤΡΟΧΗΛΑΤΟ ΚΑ∆Ο ΑΠΟΡΡΙΜΑΤΩΝ ΣΤΗΝ ΠΙΣΩ
ΟΨΗ ΤΟΥ ΜΗΧΑΝΗΜΑΤΟΣ
∆ΗΛΩΝΕΙ ΟΤΙ ΤΟ ΠΡΟΙΟΝ ΑΥΤΟ ∆ΕΝ ΠΡΕΠΕΙ ΝΑ
∆ΙΑΧΕΙΡΙΣΘΕΙ ΣΑΝ ΣΥΝΗΘΙΣΜΕΝΟ ΟΙΚΙΑΚΟ ΑΠΟΒΛΗΤΟ.
ΠΡΟΣ ΑΠΟΦΥΓΗ ΕΝ∆ΕΧΟΜΕΝΗΣ ΕΠΙΒΑΡΥΝΣΗΣ ΤΟΥ
ΠΕΡΙΒΑΛΛΟΝΤΟΣ, ΞΕΧΩΡΙΣΤΕ ΤΟ ΠΡΟΙΟΝ ΑΠΟ ΤΑ
ΑΛΛΑ
ΣΗΜΑ
ΜΕ
ΤΟΝ
∆ΙΑΓΕΓΡΑΜΜΕΝΟ
RIFIUTI
L'etichetta del cassonetto barrato riportato sul retro
dell'apparecchio indica che il prodotto non deve essere smaltito
tramite la procedura normale di smaltimento dei rifiuti domestici.
Per evitare eventuali danni all'ambiente, separare questo prodotto
da altri rifiuti domestici in modo che possa venire riciclato in base
alle procedure di rispetto ambientale. Per maggiori dettagli
sulle aree di raccolta disponibili, contattate l'ufficio govenativo
locale od il rivenditore del prodotto.
ΑΠΟΡΡΙΜΑΤΑ ΩΣΤΕ ΝΑ ΕΞΑΣΦΑΛΙΣΘΕΙ Η ΑΝΑΚΥΚΛΩΣΗ
ΤΟΥ ΜΕ ΤΟΝ ΠΡΕΠΟΝΤΑ ΤΡΟΠΟ.
ΠΑΡΑΚΑΛΟΥΜΕ ΝΑ ΕΠΙΚΟΙΝΩΝΗΣΕΤΕ ΜΕ ΤΗΝ ΤΟΠΙΚΗ
FACHGERECHTE ENTSORGUNG:
ΥΠΗΡΕΣΙΑ ΑΝΑΚΥΚΛΩΣΗΣ
Η
ΜΕ ΤΟ ΚΑΤΑΣΤΗΜΑ
Das auf der Geräterückseite angebrachte Label deutet
darauf hin, dass das Produkt nicht mit konventionellem
Hauskehricht entsorgt werden darf. Um Schäden und
Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das
Produkt fachgerecht entsorgt und von anderem Abfall getrennt
werden. Wenden Sie sich bei Fragen hierzu an Ihren Fachhändler
oder an eine öffentliche Informationsstelle.
ΑΓΟΡΑΣ ΓΙΑ ΠΕΡΙΣΣΟΤΕΡΕΣ ΛΕΠΤΟΜΕΡΕΙΕΣ.
Issue 1
Page 5 of 12
INSTALLATION
AMS50
SETTING UP
OUTPUTS:
Position the AMS50 on a stable, horizontal surface
where there is no risk of it being knocked.
Make sure ALL units involved are switched off and
unplugged from mains supply before making or
removing any connections.
Connect loudspeakers to the terminals near the base of
the back panel marked as OUTPUTs. Make sure (+)
lead from amplifier speaker output goes to (+) lead on
speaker terminals, and (-) to (-). It is most important to
get the phase of these leads correct.
During normal use, a class A amplifier, such as the
AMS50, develops an appreciable amount of internal
heat. It should therefore be sensibly situated where it can
radiate this heat most efficiently. If this is not realised,
heat build-up will occur and may cause the amplifier to
shut itself down. It is thus recommend that the unit is
situated in an open rather than enclosed space and away
from other sources of heat.
MAINS POWER INPUT
Check the rear panel mains switch is set to “off”.
Connect the supplied mains lead to the IEC socket near
base of back panel. Connect the other end to a mains
power socket.
TRIGGER INPUT
A remote triggering input is available to allow the
amplifier to be turned on automatically by other
equipment. This is a 2-way 3.5mm jack on the back of
the unit labelled “TRIGGER”. It requires 5 to 12V
(either polarity) to switch the amplifier on. Such a
trigger signal is available from (for example) most home
theatre setups.
AUDIO CONNECTIONS
Inputs: The AMS50 has a pair of RCA (single ended),
and XLR (balanced) level inputs. Choose which inputs
are to be used. It is recommended using the XLR inputs
if your preamp features XLR balanced outputs to obtain
maximum benefits of the balanced circuits.
Either the RCA or XLR inputs can be used at any one
time. It is not possible, for example, to connect both
RCA and XLR sources and use the switch to select
between the two.
Note: The trigger input acts as override to the front
panel push switch only. The unit will need to be
switched ‘on’ using the rocker switch at the back in
order for the trigger input to work.
FOR XLR INPUTS:
CAUTION!!
The XLR balanced input allows direct connection from
a pre-amplifier’s balanced outputs where available. This
provides a trap for external noise and distortion artefacts
whilst allowing the signal through completely
unaffected.
This unit features a BRIDGED output and should NOT
be grounded on either output terminal as both are
effectively “hot”. Please check if using any active
“sub”, electrostatic, or other non standard speaker types
directly connected to the outputs of the AMS50. Consult
speaker manual or supplier if in doubt.
Make sure the RCA/XLR selector slide switch on the
back panel is set correspondingly (down).
Additional note-
If bi-amping, please ensure that speaker shorting links
linking treble and bass units are removed. Failure to do
so may result in damage to connected amplifier(s)
and/or the AMS50 itself. See loudspeaker instructions
for more information.
FOR RCA INPUT:
The RCA line input allows connection from a
preamplifier or amplifier’s preamp RCA (single ended)
outputs.
Use phono to phono cables to connect the left and right
outputs on the preamplifier outputs to the left and right
line level inputs on the AMS50.
Make sure the RCA/XLR selector slide switch on the
back panel is set correspondingly (up).
CLEANING
Before cleaning the unit, switch off power at the mains
switch and remove the mains plug from the wall socket.
Clean the cabinet and remote control unit using a moist
cloth. We do not advise using solvents, white spirit or
thinners as they could damage the surface finish.
Note: in both input cases it is assumed that the driving
preamplifier has a VOLUME CONTROL to allow
setting of listening level. This is important as the
AMS50 has no volume control of its own.
Issue 1
Page 6 of 12
AMPLIFIER CONNECTIONS
AMS50
FRONT PANEL
1
2
3
4
5
6
7
1. LEFT CHANNEL Mains LED
2. LEFT CHANNEL Operate LED
3. LEFT CHANNEL Temperature LED
4. POWER Switch
5. RIGHT CHANNEL Temperature LED
6. RIGHT CHANNEL Operate LED
7. RIGHT CHANNEL Mains LED
BACK PANEL
8. DUAL RIGHT SPEAKER Output binding posts
9. RIGHT XLR Balanced input socket
10. RIGHT RCA Input socket
12. LEFT RCA Input socket
13. LEFT XLR Balanced input socket
14. DUAL LEFT SPEAKER Output 4mm binding posts
11. XLR/RCA Input selector switch
8
9
10
11
12
13
14
15
16
17
17. MAINS INLET IEC socket
15. MAINS ON/OFF switch
16. TRIGGER input 3.5mm jack
Issue 1
Page 7 of 12
AMPLIFIER OPERATION
AMS50
POWER ON
Once all connections are made, switch on the unit, using
the ON/OFF rocker switch on the back panel. On the
front panel of the AMS50 the front MAINS LEDs glow
to indicate mains is present.
To switch the unit on use front panel button, press once
and the operate LEDs will light (and mains LEDs
extinguish), indicating the unit is ready for use.
Alternatively, using the TRIGGER input, switch on
the triggering unit (preamp, Home Theatre processor,
etc) and the AMS50 will come on automatically.
OVERHEAT
Should any internal overheat situation have been
reached, the amplifier will cut out, there will be no more
sound output, and the orange LED will light.
Unit will remain in this state until it has cooled down
again. If overheat mode persists, check wiring for errors,
and locate unit where it can cool down more easily.
Issue 1
Page 8 of 12
AMPLIFIER SPECIFICATIONS
AMS50
Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment. Always
check the most obvious possible causes first, such as the following examples:
Problem
Probable Cause
Remedy
No power when POWER switched
turned on
Mains power plug is not fully inserted Plug in securely
into rear socket
No mains power
Check socket with another appliance
Unit not coming on via TRIGGER
input
Mains power not present
Check unit is plugged in and switched
on (back panel switch).
Trigger lead disconnected
Triggering unit not sending trigger
signal
Check lead is fully connected and
triggering unit is on and sending a
trigger signal (±5 to 12V nominal)
Move RCA/XLR switch to correct
position
Noisy or reduced sound
Wrong input selected
Both RCA and XLR inputs connected Remove unwanted source.
to source(s)
Sound is not precise, lacking in bass
and stereo image (when used in
conjunction with other unit(s))
Speakers are connected out of phase,
i.e., connections to one speaker (+
and -) are reversed on one or more
units
Ensure speakers are connected
correctly:
+ terminal on amplifier goes to +
terminal on speaker,
- terminal on amplifier goes to –
terminal on speaker.
Note: Most cables have polarity
markings to help get this right.
Make sure unit is situated to allow
free air circulation. Allow to cool
down before attempting to switch on
again
Unit cuts out, orange LED lit
Flashing RED LED
Overheating
Short circuit in speaker (output) leads Check speaker leads connected to
SPEAKER OUTs on AMS50 and
speaker ends for stray strands or short
circuits.
Problem in speakers
Grounded via speaker
Check speakers and wiring.
Wait 30 seconds before switching
back on, and apply music source.
Both the + and – speaker output
terminals on this unit are “hot”. Some
speakers e.g. active subs and
electrostatics have “grounded” inputs.
Such speakers are incompatible with
the AMS50.
Hum
Audio connector plug not fully
pushed in
Input not correctly selected
Cable Fault
Insert plug securely
Move input switch to correct position
Check cable is connected at both
ends.
Unsuitable Cable
(e.g. cable grounds not connected)
N.B. some esoteric cables have
internal wiring intentionally
disconnected/modified. For best
results on all inputs, please use good
quality straight- through cables,
signal lead(s) directly connected at
both ends and earth/screen(s) directly
connected at both ends.
If none of these actions affect a cure, please contact your dealer, or an authorised Musical Fidelity service agent.
Remember; never open the case of the AMS50 yourself, as this will invalidate the guarantee.
Issue 1
Page 9 of 12
AMPLIFIER SPECIFICATIONS
AMS50
Issue 1
Page 10 of 12
AMPLIFIER SPECIFICATIONS
AMS50
Output:
Power
50 Watts per channel into 8 Ohms (17dBW),
100 Watts per channel into 4 Ohms
Voltage, RMS
20 Volts 20Hz to 20 kHz
58 Volts
100 Amps
Voltage, Peak-to-peak
Current peak-to-peak
Damping factor
190
Output devices
12 per channel
Thermal cut out (internal temp) 70ºC
Balanced Line input:
THD + noise, 20Hz to 20 kHz < 0.006% unwtd.
Signal to noise ratio > 110dB ‘A’-weighted
Input sensitivity for 50 Watts 650mV
Input impedance
50k Ohms
Frequency response
10Hz to 40 kHz, +0, -0.4dB
Connections:
Line level inputs
1 pair line level XLR (balanced) connectors
1 pair line level RCA connectors
4 pair 4mm banana plug/binding posts
3.5mm/⅛” mono jack socket
±5V to ±12V
Speaker outputs
Trigger input
Trigger level
Power requirement:
Mains voltages:
115/230VAC 50/60Hz (factory pre-set)
100VAC 50/60Hz (alternative)
600 Watts maximum into 8 Ohms
14 Watts idle (mains LEDs lit)
Consumption:
Weight:
60 kg
65 kg
132 lbs
143 lbs
unit only, unboxed
in shipping carton
Dimensions: 483 mm
325 mm
19 inches
12¾ inches
18¼ inches
wide
high including feet
deep (front to back) including terminals
460 mm
Standard accessories:
IEC type mains lead (10-Amp type),
Musical Fidelity reserves the right to make
improvements which may result in specification or
feature changes without notice.
Issue 1
Page 11 of 12
MANUAL REVISION
AMS50
RELEASE
DATE
CHANGES
Issue 1
28th May 2009-05-28
1st issue
Issue 1
Page 12 of 12
|