Oregon Scientific Weather Radio RMR383HGA User Manual

1. Heat Index icon  
4. Close the battery compartment.  
5. Secure the sensor in the desired location using the wall  
mount or table stand.  
2. Hi / lo temperature alarm  
3. Max / min temperature icon  
4. Sensor reception icon  
5. Comfort Zone  
6. Battery low icon  
7. Hi / lo humidity alarm  
8. Max / min humidity icon  
9. Ice warning is active  
10. Temperature trend  
11. Temperature  
Wireless Indoor / Outdoor Thermometer  
with Indoor Humidity and  
Self-Setting Atomic Clock  
Model: RMR383HGA  
12. Heat Index warning  
13. Humidity  
14. Humidity trend  
For best results:  
USER MANUAL  
INTRODUCTION  
Thank you for selecting this Oregon ScientificTM Wireless  
Indoor / Outdoor Thermometer with Indoor Humidity and Self-  
Setting Atomic clock (RMR383HGA). This clock is supplied  
with a remote sensor (THN132N) and can support up to 3  
sensors in total (additional sensors sold separately).  
Place the sensor out of direct sunlight and moisture.  
Do not place the sensor more than 30 m (100 ft) from the  
main (indoor) unit.  
Position the sensor so that it faces the main (indoor)  
unit, minimizing obstructions such as doors, walls, and  
furniture.  
Place the sensor in a location with a clear view to the  
sky, away from metallic or electronic objects.  
Position the sensor close to the main unit during cold  
winter months as below-freezing temperatures may affect  
battery performance and signal transmission.  
Clock / Alarm area:  
NOTE Please keep this manual handy as you use your new  
product. It contains practical step-by-step instructions, as well  
as technical specifications and warnings you should know  
about.  
The transmission range may vary depending on many factors.  
You may need to experiment with various locations to get  
the best results.  
1. Clock signal reception  
2. AM / PM mode selected  
3. Alarm mode  
4. Alarm set  
5. AM / PM mode selected  
6. Alarm time  
CLOCK OVERVIEW  
Standard Alkaline batteries contain significant amounts of  
water. Because of this they will freeze in low temperatures  
of approximately -12°C (10°F). Disposable Lithium batteries  
have a much lower threshold for temperature with an  
estimated freezing range of below -30°C (-22°F).  
FRONT VIEW  
7. US time zone  
8. Clock  
9. Moon phase  
Wireless ranges can be impacted by a variety of factors  
such as extremely cold temperatures. Extreme cold may  
temporarily reduce the effective range between the sensor  
and the base station. If the unit’s performance fails due to  
low temperature, the unit will resume proper functioning as  
the temperature rises to within the normal temperature range  
(i.e. no permanent damage will occur to the unit due to low  
temperatures).  
REMOTE SENSOR (THN132N)  
SENSOR DATA TRANSMISSION  
The sensor reception icon in the temperature and humidity  
area shows the status.  
ICON  
DESCRIPTION  
1. SNOOZE  
2. Temperature and Humidity Area  
3. Clock / Alarm Area  
Main unit is searching for the  
sensor(s)  
A channel has been found and  
sensor signal is being received  
4. ALARM: View alarm status; set alarm  
and “- - . -“  
(Temperature  
and Humidity Area)  
The sensor cannot be found.  
Search for the sensor or  
check batteries  
BACK VIEW  
To search for a sensor:  
Simultaneously, press and hold MEM and CHANNEL for  
2 seconds.  
1. LED indicator  
1. Wall mount  
2. Battery compartment  
3. Battery door  
4. Table stand  
5. RESET  
NOTE If the sensor is still not found, check the batteries,  
obstructions, and remote unit location.  
6. CHANNEL switch  
CLOCK  
CLOCK RECEPTION  
GETTING STARTED  
BATTERIES  
Insert batteries before first use, matching the polarity (+ and  
-). Press RESET after each battery change.  
This product is designed to synchronize its date and time  
automatically once it is within range of the WWVB-60  
signal from the atomic clock in Fort Collins, Colorado.  
The clock collects the radio signals whenever it is within 3219  
km (2000 miles) of a signal.  
NOTE Press ZONE to select the US time zone: Pacific (P),  
 
Eastern (E), Central (C) or Mountain (M).  
NOTE Initial reception takes 2-10 minutes for first set up or  
when RESET is pressed. Once complete, the reception icon  
will stop blinking. If the signal is weak, it can take up to 24  
hours to get a valid signal.  
1.  
/
: Increase / decrease setting; activate /  
deactivate clock reception signal  
2. MODE: Change settings / display  
3. CHANNEL: Switch remote sensor display  
4. MEM: View current, maximum and minimum  
temperature / humidity  
5. °C / °F: Select temperature unit  
6. HEAT INDEX  
RECEPTION SIGNAL  
Clock signal reception indicator:  
indicates main unit batteries are low.  
NOTE Do not use rechargeable batteries. We recommend  
that you use alkaline batteries with this product for longer  
usage and lithium batteries in temperatures below freezing.  
STRONG SIGNAL  
WEAK SIGNAL NO SIGNAL  
7. TEMP / HUMIDITY HI / LO  
: Change settings  
or enable / disable hi or lo temperature / humidity  
alarm  
8. RESET: Reset unit to default settings  
9. ZONE: Toggle US time zone  
10. Battery compartment  
REMOTE SENSOR  
The sensor collects temperature readings approx. every 40  
seconds and sends them to the main unit. The main unit can  
collect data from up to 3 sensors.  
To set up the sensor:  
1. Slide open the battery door.  
2. Insert the batteries, matching the polarity (+ / -). Reset  
the sensor after each battery change.  
3. Select a channel. Make sure you use a different channel  
for each sensor.  
To enable and force a signal search:  
Press and hold for 2 seconds.  
To disable the signal reception:  
Press and hold  
for 2 seconds.  
LCD DISPLAY  
Temperature and Humidity area:  
SET CLOCK  
If the clock signal reception is enabled and a signal is being  
received the clock does not need to be manually set.  
 
To manually set the clock:  
1. Press and hold MODE for 2 seconds.  
��  
 
2. Press  
and  
to change the settings.  
3. Press MODE to confirm.  
 
4. The setting sequence is: 12/24 hour format, hour, minute,  
year, date / month format, month, date, and display  
language.  
�  
RMR383HGA_M_R6  
1
2006.4.7, 10:19 AM  
 

MTD Yard Vacuum 243 670 User Manual
National Instruments Stereo Receiver NI PXI 4224 User Manual
Nikon Cell Phone Accessories D600 User Manual
Nintendo Video Games 658A61A User Manual
Nortel Networks Telephone 413X User Manual
Numark Industries Karaoke Machine KMX02 User Manual
Omega Engineering Welder DP41 E User Manual
Omron Network Card CJ2 User Manual
Onkyo DVD Player DV SP406 User Manual
Panasonic Home Theater Screen PT 53WX54 User Manual